MT70014 vlsi components for arinc 429 data transmission systems 1 two channel arinc transmitter 8 bit parallel interface ttl/cmos compatible i/p single 5v supply with low power consumption < 50mw full mil operating range automatic parity generation high/low speed programmable independently in each channel
MT70014 vlsi components for arinc 429 data transmission systems 2 maximum ratings (above which the useful life may be impaired) storage temperature - 65oc to +150oc temperature (ambient) under bias - 55oc to +125oc supply voltage vdd -0.3v to + 7v dc input voltage -0.3 to vdd +0.3v output current (single o/p) 10ma output current (total o/p) 20ma electrical characteristics over operating range parameter description test conditions min typ max units ioh output high current voh=2.8v vdd= 4.5v 1.0 ma iol output low current vol=0.4v 3.2 ma vih input high voltage 2.4 vcc volts vil input low voltage -0.3 0.8 volts iil input load current vss 0.45 ma ioz output leakage current 0.4v < vo < vcc output disabled -40 40 ua ci input capacitance test frequency = 1.0 mhz 2 2.6 pf ci/o i/o capacitance 7 9 pf icc supply current vcc = max. all inputs high, all outputs open . 1.5 ma
MT70014 vlsi components for arinc 429 data transmission systems 3 3. switching characteristics (for c l = 50pf & rl = 3k ohms) parameter min max units f clk clock frequency - 5 mhz t p ( s erial data bit period for hnl input high 50/f us ( ( serial data bit period for hnl input low 380/f us ( ( (f = f clk /mhz) t res nrset pulse width 200ns - t rtc propagation delay, nreset falling edge to txc high - 200ns t rd propagation delay, nreset falling edge to data outputs low - 200ns t wl nld pulse width 200ns - t gl gap between nld pulses 400ns - t su data set up time 100ns - t h data hold time 100ns - t lt c propagation delay, nld rising edge following last - 400ns byte load to txz low t r output rise time - 50ns t f output fall time - 50ns t wte not transmit enable pulse width 100ns - t ted propagation delay not transmit enable falling ) edge or ) tp 2tp not transmission complete falling edge to ) data output ) t dtc last data bit of message to txc high - 200ns t m time of data pulse output (mark time) tp + 1% 2
MT70014 vlsi components for arinc 429 data transmission systems 4 functional description the device consists of two independent channels each of which functions as a parallel to serial data converter. the parallel data is loaded via an 8-bit input highway and the serial output is generated in the arinc format, i.e. 31 bits of data plus one parity bit. the input highway (dio to d17) is common to both channels as are the reset (nreset) clock 9clock), positive supply (v dd ), and ground (vss) pins. each channel has 3 control inputs. channel 0 has a ?load? input (nldo), a ?transmit enable? input (ntxeo), and a ?high/low speed? (hnlo) control input. there are 3 outputs per channel. channel 0 has a ?data out zeros? (zdo) output, a ?data out ones? (odo) output and a ?transmission complete? (txco) output. operations for channel 0 and channel 1 are identical in all respects. the data to be transmitted by a particular channel is loaded as four 8-bit bytes via the input highway. the four bytes are stored on chip in the order in which they were loaded. loading is performed by pulsing the (nldo) input low. the data must then be changed to the value of the next byte and (nldo) pulsed low again etc. the four bytes are transmitted in the order in which they were loaded. the only exception is the most significant bit of the 4th byte. this bit is ignored and a parity bit is transmitted in its place. the parity bit corresponds to an odd parity check on the first 31 bits, i.e. if the number of ones in the first 31 bits is odd, the parity bit is equal to zero. data is only accepted if the txco output is high. once byte 4 has been loaded, txco is driven low. data must be valid on the input highway for t su before and to t h after the (nldo) rising edge. the clock (clock ) input of 5mhz + 1%* is divided down on chip by 50 to give a serial data transmission rate for (hnlo) high or by 380 for (hnlo) low. these rates correspond to the arinc fast and slow rates respectively. the timing of the two output data lines (odo) and (zdo) is shown in fig.2. a data value of one is signified by a positive pulse output on (odo) and a zero by a positive pulse on (zdo). the bit period tp will be 50/ f clk for (hnlo) high and 380/f clk for (hnlo) low. * arinc recommends that the transmission rate should not be precisely 100khz to avoid interference but any rate within + 1% of these can be used. the overall timing diagram for a complete data transfer is shown in fig.3. when the last byte has been loaded (txco) goes low. this signal is combined with the output of an on chip latch which is set by the (ntxeo) signal to initiate the start of transmission. the latch is reset upon start of transmission. if the (ntxeo) signal is left permanently low the on chip latch is always set and transmission will be initiated by txco going low, i.e. as soon as the 4 bytes have been loaded. hence there is an option between auto-start and controlled-start of transmission. at the end of the transmission txco goes high and the device is able to accept new dat a. the devices can be completely reset by pulsing the (nreset) line low. this causes both channels to be put into the data load phase of operation. the txc lines are forced high and all data outputs are forced low. the timing is shown in fig. 4. interface definitions the device is implemented as a monolithic circuit using cmos compatible with standard tll circuitry. a circuit with v oh (min) = 2.7v and v ol (max) = 0.4v will drive all inputs to the device and a standard ttl circuit with i il (max) = -1.6ma at v i = 0.4v and i ih (max) = 40 ua at v i = 2.4v can be driven by all the outputs of the device.
MT70014 vlsi components for arinc 429 data transmission systems 5 an on-chip resistor of nominal value 25k ohms is connected between the input pin and v dd . this is intended to pull up the input to a sufficiently high voltage to ensure switching when a standard ttl driver is driving the input.
MT70014 vlsi components for arinc 429 data transmission systems 6
MT70014 vlsi components for arinc 429 data transmission systems 7
|
